Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 3
Button_value = 7
Hit any key to stop autoboot: 0
STB7100-REF> ## Booting image at a0040000 ...
STB7100-REF> bootm a0040000
## Booting image at a0040000 ...
Image Name: Linux-2.6.17.14_stm22_0037
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1783856 Bytes = 1.7 MB
Load Address: 84401000
Entry Point: 84402000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/nfs nfsroot=/nfs/target_enigma2
rw ip=192.168.1.34:192.168.1.241:192.168.1.1:255.255.255.0:kathrein:eth0:off mem
=64m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:0:5
0:fd:ff:78:ce - 0x00000000 - 0 ...
Linux version 2.6.17.14_stm22_0037 (rarr@KnopBox) (gcc-Version 4.1.1 (STMicroele
ctronics/Linux Base 4.1.1-23)) #1 PREEMPT Wed Jul 16 12:06:17 CEST 2008
STMicroelectronics STb7100 Reference board initialisation
STb7100 version 3.x
Built 1 zonelists
Kernel command line: console=ttyAS0,115200 root=/dev/nfs nfsroot=/nfs/target_eni
gma2 rw ip=192.168.1.34:192.168.1.241:192.168.1.1:255.255.255.0:kathrein:eth0:of
f mem=64m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwadd
r:0:50:fd:ff:78:ce
st-coprocessor: Failed to reserve memory at 0x10000000
st-coprocessor: Failed to reserve memory at 0x10400000
PID hash table entries: 512 (order: 9, 2048 bytes)
Using tmu for system timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61312k/65536k available (2985k kernel code, 4188k reserved, 368k data, 9
6k init)
PVR=04061100 CVR=30480000 PRR=00009100
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STb710x
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Installing knfsd (copyright (C) 1996 [email][email protected][/email]).
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Device probe found data for platform device lirc
lirc_dev: IR Remote Control driver registered, at major 61
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_dev: lirc_register_plugin: plugin lirc_stm owner 00000000
STM LIRC plugin has IRQ 125
Lirc STM: Using IRB mode
STMicroelectronics LIRC driver configured
STPIO layer initialised
VFD_Controller Type : NEW Kathrein VFD
STMicroelectronics ASC driver initialized
ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
s_env_mac[0] = 0
s_env_mac[1] = 0
s_env_mac[2] = :
s_env_mac[3] = 5
s_env_mac[4] = 0
s_env_mac[5] = :
s_env_mac[6] = f
s_env_mac[7] = d
s_env_mac[8] = :
s_env_mac[9] = f
s_env_mac[10] = f
s_env_mac[11] = :
s_env_mac[12] = 7
s_env_mac[13] = 8
s_env_mac[14] = :
s_env_mac[15] = c
s_env_mac[16] = e
get ether addr = 0, 50, fd, ff, 78, ce
mac hi address = ce78, lowaddress = fffd5000
SMSC: --> init_module()
SMSC: Driver Version = 1.21
SMSC: Compiled: Jul 16 2008, 12:05:15
SMSC: Platform: ST40 STMICRO r3
SMSC: Driver Parameters
SMSC: lan_base = 0x00000000, driver will decide
SMSC: bus_width = 0, driver will autodetect
SMSC: link_mode = 0x7F, 10HD,10FD,100HD,100FD,ASYMP,SYMP,ANEG
SMSC: irq = 2
SMSC: int_deas = 0xFFFFFFFF, use platform default
SMSC: irq_pol = 1, IRQ output is active high
SMSC: irq_type = 1, IRQ output is Push-Pull driver
SMSC: rx_dma = 256, RX will use PIO
SMSC: tx_dma = 256, TX will use PIO
SMSC: dma_threshold = 200
SMSC: mac_addr_hi16 = 0x0000CE78
SMSC: mac_addr_lo32 = 0xFFFD5000
SMSC: debug_mode = 0x00000007
SMSC: tx_fif_sz = 0x00050000
SMSC: afc_cfg = 0xFFFFFFFF, driver will decide
SMSC: tasklets = 0, Tasklets disabled
SMSC: phy_addr = 0xFFFFFFFF, Use internal phy
SMSC: max_throughput = 0xFFFFFFFF, Use platform default
SMSC: max_packet_count = 0xFFFFFFFF, Use platform default
SMSC: packet_cost = 0xFFFFFFFF, Use platform default
SMSC: burst_period = 0xFFFFFFFF, Use platform default
SMSC: max_work_load = 0xFFFFFFFF, Use platform default
SMSC: -->Smsc911x_init(dev=0x847074D0)
SMSC: --> Platform_Initialize
SMSC: Lan Base at 0xA2000000
SMSC: <-- Platform_Initialize
SMSC: dwLanBase=0xA2000000
SMSC: LAN9115 identified, dwIdRev==0x01150002
SMSC: FPGA_REV == 0x00000000
SMSC: <--Smsc911x_init(), result=0
SMSC: Interface Name = "eth0"
SMSC: <-- init_module()
Failed to parse ether addr: 0:50:fd:ff:78:ce
ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170
ata1: SATA link down (SStatus 0)
scsi0 : sata_stm
Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Onboard_Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 2
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 11 MTD partitions on "Onboard_Flash":
0x00000000-0x00020000 : "Boot firmware : 0xA000.0000-0xA001.FFFF"
0x00040000-0x00200000 : "Kernel - 0xA004.0000-0xA01F.FFFF"
0x00200000-0x002a0000 : "Config FS - 0xA020.0000-0xA029.FFFF"
0x002a0000-0x004e0000 : "Root SQUASHFS- 0xA02A.0000-0xA04D.FFFF"
0x004e0000-0x00ae0000 : "APP_Modules 0xA04E.0000-0xA0AD.FFFF"
0x00ae0000-0x00c00000 : "EmergencyRoot 0xA0AE.0000-0xA0BF.FFFF"
0x00c00000-0x00fc0000 : "OtherData Var 0xA0C0.0000-0xA0FB.FFFF"
0x00020000-0x00040000 : "BootConfiguration 0xA002.0000-0xA003.FFFF"
0x00fc0000-0x00fd0000 : "2nd BootConfiguration 0xA0FC.0000-0xA0FC.FFFF"
0x00fd0000-0x01000000 : "2nd Boot firmware : 0xA0FD.0000-0xA0FF.FFFF"
0x00040000-0x01000000 : "Flash wo/ Bootloader 0xA004.0000-0xA0FF.FFFF"
ST40_start_host_control
ST40_start_host_control proceeding
ST40-ehci ST40-ehci.2: ST EHCI Host Controller
ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1
ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00
ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: ST EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17.14_stm22_0037 ehci_hcd
usb usb1: SerialNumber: STB7100_EHCI
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ST40-ehci and address 2
usb 1-1: Product: USB2.0 Hub
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver libusual
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
stssc layer initialized
STMicroelectronics - Coprocessors st231 Init
st231-0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0000000 size 0x00400000
cop. addr 0x10000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231-1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0400000 size 0x00400000
cop. addr 0x10400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
TCP bic registered
TCP highspeed registered
NET: Registered protocol family 1
NET: Registered protocol family 17
SMSC: -->Smsc911x_open(dev=0x847074D0)
SMSC: -->Lan_Initialize(dwIntCfg=0x00000011)
SMSC: <--g_GpioSetting set
SMSC: <--Lan_Initialize
SMSC: Testing ISR using IRQ 2
SMSC: ISR passed test using IRQ 2
SMSC: Mac Address is set by parameter to 0xCE78FFFD5000
SMSC: -->Phy_Initialize
SMSC: dwPhyId==0x00C0001C,bPhyModel==0x0D,bPhyRev==0x01
SMSC: Successfully Verified Loop Back Packet
SMSC: Passed Loop Back Test
SMSC: <--Phy_Initialize, result=TRUE
SMSC: Tx will use PIO
SMSC: Rx will use PIO
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: <--Smsc911x_open, result=0
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: Multicast: enable dwBitNum=31,addr=01 00 5E 00 00 01
IP-Config: Complete:
device=eth0, addr=192.168.1.34, mask=255.255.255.0, gw=192.168.1.1,
host=kathrein, domain=, nis-domain=(none),
bootserver=192.168.1.241, rootserver=192.168.1.241, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.241
SMSC: Link is now UP at 100Mbps FD
SMSC: LAN911x: ASYMP,SYMP ,100FD,100HD,10FD ,10HD
SMSC: Partner: ,SYMP ,100FD,100HD,10FD ,10HD
SMSC_WARNING: Gpt_CancelCallBack: Failed
portmap: server 192.168.1.241 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.241
f
